Eurocode 2 offers various methods for determining the stress-strain relationship of concrete in flexure. For simplicity and familiarity the method presented here is the simplified rectangular stress block (which is similar to that found in BS 8110). In determining the resistance of sections, the following assumptions are made.

  • Plane sections remain plane.
  • Strain in the bonded reinforcement, whether in tension or compression, is the same as that in the surrounding concrete.
  • Tensile strength of the concrete is ignored.
  • Stress distribution in the section is as shown in Figure 2 - simplified rectangular stress block
  • Stresses in reinforcement are derived from Figure 6.2

Figure 2: Simplified rectangular stress blockfor concrete up to class C50/60 from Eurocode 2

提取How to Design Concrete Structures using Eurocode 2(page 64, Figure 2)

Figure 6.2: Idealised and design stress-strain diagrams for reinforcing steel (for tension and compression)

Extract fromConcise Eurocode 2(第37页,图6.2)(检查应变限制时,可以使用设计线的倾斜分支。)

Proof: singly reinforced beams and slabs

The majority of beams and slabs used in practice are singly reinforced. Design equations for the amount of reinforcement required can be derived as follows (refer to Figure 2 above):

Fc= (0.85fck/ 1.5)b(0.8x)= 0.453fckb x
Fst= 0.87Asfyk

Take moments about the centre of the tension force
M= 0.453fckb x z. . . . . . . (1)
Nowz=d- 0.4x
\x= 2.5(d-z)
&M= 0.453fckb2.5(d-z)z
= 1.1333 (fckb z d - fckb z2)
LetK=M/ (fckb d2)
\ 0 = 1.1333 [(z/d)2– (z/d)] +K
0 = (z/d)2– (z/d) + 0.88235K
Solving the quadratic equation:
z/d= [1 + (1 - 3.529K)0.5]/2
z=d(1 + (1 - 3.529K)0.5]/2

So the lever arm for an applied moment is known
Take moments about the centre of the compression force
M= 0.87Asfykz


The required area of reinforcement can now be calculated. For convenience for hand calculations, tables of values of z/d according to K are published, for instance inConcise Eurocode 2and inHow to Design Concrete Structures using Eurocode 2,page 33, Table 5.

Limiting neutral axis depth

As a beam experiences more moment, it is often considered good practice to limit the depth of the neutral axis to avoid ‘over-reinforcement’ (i.e. to ensure that the reinforcement has passed its yield point). This is not a Eurocode 2 requirement and is not accepted by all engineers. A limiting value forKcan be calculated (denotedk’) as follows.

ecu3= 0.0035 =混凝土应变(来自EN1992-1-1表3.1)
es= 500 / (1.15 x 200 x 103) = 0.0022 = reinforcement strain

From strain diagram:
x= 0.0035d/(0.0035 + 0.0022)

= 0.6d

From Eqn 1 above:
M= 0.453fckb x z
M’ = 0.453fckb0.6d (d– 0.4 x 0.6d)
= 0.207fckb d2

\ K= 0.207

Beyondk’compression reinforcement is required. Neutral axis depth x varies with the amount of redistribution of moments.k’= 0.207在没有重新分配但重新分配15%的情况下有效k’= 0.168 is appropriate. In the UK it is often recommended thatk’should be limited to 0.168 to ensure ductile failure.

Proof: compression reinforcement

In some cases, compression reinforcement is added to increase section strength where section dimensions are restricted i.e. whereK > K’. It may also be added to reduce long term deflection or to decrease curvature/deformation at ultimate limit state. It may also be added to reduce long term deflection or to decrease curvature/deformation at ultimate limit state.

With respect to Figure 1, we now need to consider an extra forceFsc= 0.87As2fyk

The area of tension reinforcement can now be considered in two parts, the first part to balance the compressive force in the concrete, the second part is to balance the force in the compression steel. The area of reinforcement required is therefore:

As=Kfcub d2/(0.87fykz)+As2
wherezis calculated usingK’ instead ofK

As2can be calculated by taking moments about the centre of the tension force:
M=Kfcub d2+ 0.87fykAs2(d-d2)

As2= (K-K”)fcub d2/(0.87fyk(d-d2))

High strength concretes

Eurocode 2 gives recommendations for the design of concrete up to class C90/105. However, for concrete greater than class C50/60, the concrete compression stress block is modified (See EN 1992-1-1 Cl. 3.1.7(3).

How to Design Concrete Structures using Eurocode 2: Second edition

Concise Eurocode 2